350 kcmil Voltage Drop at 120V
This page provides detailed voltage drop analysis for 350 kcmil conductors operating at 120V (single-phase). The 350 kcmil copper conductor has a resistance of 0.0367 ohms per 1000 feet and an ampacity of 310 amps at 75 degrees C per NEC Table 310.16. Use the tables below to determine the voltage drop at any distance and amperage combination, or to find the maximum distance you can run 350 kcmil wire while staying within the NEC recommended voltage drop limits.
Maximum Distance for 350 kcmil at 120V
The table below shows the maximum one-way distance you can run 350 kcmil copper conductor at 120V for each amperage level while maintaining voltage drop at or below 3% (branch circuit) and 5% (feeder + branch combined). If your planned run exceeds these distances, you must use a larger wire gauge. These values assume single-phase power with a 2 multiplier in the voltage drop formula.
| Amperage | Max Distance (3%) | Max Distance (5%) | 3% Drop = 3.6V |
|---|---|---|---|
| 5A | 9809 ft | 16348 ft | 3.6 V |
| 10A | 4904 ft | 8174 ft | 3.6 V |
| 15A | 3269 ft | 5449 ft | 3.6 V |
| 20A | 2452 ft | 4087 ft | 3.6 V |
| 25A | 1961 ft | 3269 ft | 3.6 V |
| 30A | 1634 ft | 2724 ft | 3.6 V |
| 40A | 1226 ft | 2043 ft | 3.6 V |
| 50A | 980 ft | 1634 ft | 3.6 V |
| 60A | 817 ft | 1362 ft | 3.6 V |
| 80A | 613 ft | 1021 ft | 3.6 V |
| 100A | 490 ft | 817 ft | 3.6 V |
Voltage Drop Table — 350 kcmil Copper at 120V
Complete voltage drop matrix for 350 kcmil copper conductor at 120V. Each cell shows the voltage drop in volts and percentage. Cells in red exceed the 3% NEC recommendation for branch circuits. Cells within the green range are NEC compliant. This table uses the single-phase voltage drop formula with a conductor resistance of 0.0367 ohms per 1000 feet.
| Distance | 5A | 10A | 15A | 20A | 25A | 30A | 40A | 50A | 60A | 80A | 100A |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 25 ft | 0.0V 0.0% | 0.0V 0.0% | 0.0V 0.0% | 0.0V 0.0% | 0.1V 0.0% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.1% |
| 50 ft | 0.0V 0.0% | 0.0V 0.0% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.1% | 0.2V 0.2% | 0.3V 0.2% | 0.4V 0.3% |
| 75 ft | 0.0V 0.0% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.1% | 0.2V 0.2% | 0.3V 0.2% | 0.3V 0.3% | 0.4V 0.4% | 0.6V 0.5% |
| 100 ft | 0.0V 0.0% | 0.1V 0.1% | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.1% | 0.2V 0.2% | 0.3V 0.2% | 0.4V 0.3% | 0.4V 0.4% | 0.6V 0.5% | 0.7V 0.6% |
| 125 ft | 0.1V 0.0% | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.1% | 0.2V 0.2% | 0.3V 0.2% | 0.4V 0.3% | 0.5V 0.4% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.8% |
| 150 ft | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.1% | 0.2V 0.2% | 0.3V 0.2% | 0.3V 0.3% | 0.4V 0.4% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.7% | 1.1V 0.9% |
| 200 ft | 0.1V 0.1% | 0.1V 0.1% | 0.2V 0.2% | 0.3V 0.2% | 0.4V 0.3% | 0.4V 0.4% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.7% | 1.2V 1.0% | 1.5V 1.2% |
| 250 ft | 0.1V 0.1% | 0.2V 0.1% | 0.3V 0.2% | 0.4V 0.3% | 0.5V 0.4% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.8% | 1.1V 0.9% | 1.5V 1.2% | 1.8V 1.5% |
| 300 ft | 0.1V 0.1% | 0.2V 0.2% | 0.3V 0.3% | 0.4V 0.4% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.7% | 1.1V 0.9% | 1.3V 1.1% | 1.8V 1.5% | 2.2V 1.8% |
| 400 ft | 0.1V 0.1% | 0.3V 0.2% | 0.4V 0.4% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.7% | 1.2V 1.0% | 1.5V 1.2% | 1.8V 1.5% | 2.4V 2.0% | 2.9V 2.5% |
| 500 ft | 0.2V 0.1% | 0.4V 0.3% | 0.6V 0.5% | 0.7V 0.6% | 0.9V 0.8% | 1.1V 0.9% | 1.5V 1.2% | 1.8V 1.5% | 2.2V 1.8% | 2.9V 2.5% | 3.7V 3.1% |
When to Use 350 kcmil at 120V
350 kcmil wire at 120V is appropriate for circuits where the amperage does not exceed 310 amps (copper, 75 degrees C) and the voltage drop at the planned distance stays within NEC recommendations. At short distances under 50 feet, 350 kcmil handles 248-amp loads with comfortable voltage drop margin. As the distance increases, the voltage drop grows proportionally, and at some point a larger gauge becomes necessary.
If 350 kcmil does not provide adequate voltage drop performance for your run distance, consider the next larger gauge. Each step up in wire size roughly doubles the maximum distance for the same voltage drop percentage. Alternatively, if the circuit operates at 120 volts and the distance is problematic, consider whether the load can be served by a 240-volt circuit instead, which halves the percentage voltage drop and doubles the effective run distance for the same wire gauge.
For aluminum conductors, 350 kcmil has an ampacity of 248 amps at 75 degrees C and a resistance of 0.0605 ohms per 1000 feet. The higher resistance means aluminum requires approximately 65% more distance correction compared to copper, often requiring an increase of one or two gauge sizes to match copper's voltage drop performance at the same distance.
Related Wire Sizes at 120V
Compare voltage drop performance across different wire gauges at 120V. Larger gauges have lower resistance and can run longer distances with less voltage drop.
Tools and Training for Electricians
Quality resources for your next wiring project.
Some links above are affiliate links — if you buy through them we may earn a small commission at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.